December 22, 2017
I downloaded a number of BXY files (filename.bxy) that contained Christmas art for Apple II Programs. In the example below I used PublishIt4 to import the individual pictures.
Anyway, the bxy files contained 24 pictures each but only 8 can fit on a 5.25 disk image. Here is a picture in CiderPress. You can also create a .2mg file containing all 24 files if you want. I created all 24 on a 800k.po file and then converted it to the 2mg. Works perfectly fine in the Virtual II Emulator as long as you configure Virtual II with SCSI drives. See earlier blog post on doing this. I think you can search on OmniDisk.
I used File, Open dropdown to view contents. Then, I selected the pictures I wanted. Next, go to Actions, Convert to disk archive. Following usual CiderPress actions, Name the volume, click OK, and then save file, use same name or different name. This gives you a filename.po image which I loaded to my Virtual IIe Emulator. Below is a snapshot of PublishIt4 printout of some of the pictures.
November 20, 2017
Just installed my FASTChip //e In italics are the notes from the a2heaven.com website.
The FASTChip //e accelerates the Apple //e™ by replacing the on-board microprocessor with a much faster one. Because the memory on the Apple //e™ can only run at a 1 MHz speed maximum, faster memory (SRAM) must be provided to increase performance and allow the 65C02/65C816 CPU to run at full speed. To do this, the FASTChip //e contains 512KB/1024KB of fast SRAM memory. The clever design allows the acceleration of programs running in both main and auxiliary memory. The additional FASTChip //e memory can emulate both 192/448 KB fast RamWorks compatible RAM and 256/512 KB fast RamFactor (slinky) compatible RAM.
FASTChip //e features
- Easy to install card, installable in slot 1-7 of the Apple //e™, or Enhanced //e.
- Does not mechanically interfere with the 80 column card in slot 3.
- 65C02/65C816 microprocessor running at a clock rate of more than 16 MHz .
- External Hardware Control Panel with controls and LED display.
- CPU frequency can be changed real-time via rotary knob (0.2Mhz to 16.6Mhz).
- Stop/Pause and Status buttons for easy control.
- 4 digits x 7 segment LED display.
- Built in 192/448 KB fast RamWorks compatible RAM.
- Built in 256/512 KB fast RamFactor (Slinky) compatible RAM.
- Low power design for cool operation.
- Acceleration of programs running in both main and auxiliary memory.
- Compatible with most interface and expansion cards for the Apple II/IIe.
- Transparent operation with all Apple II software.
- An easily accessed built-in software control panel lets you control processor speed, memory, joystick, speaker sound quality and many other options.
My actual //e Setup with FastChip//e, RamWorks8M card and SDFloppy II installed.
FastChip//e videos of PublishIT version 4 at 10 Mhz. A program essentially unusable on a IIe at 1 MHz.
[Note: I’m running PublishIt from a SCSI drive, not a floppy, unidisk 3.5, or SDFloppy, although programs ran fine from all three devices. But obviously SCSI is the fastest ] : unless you have a CFFA or MicroDrive Turbo.
December 15, 2016
A drive I picked up. It actually works. Now a lot of external and maybe some internal cleaning is in order.
If you look closely there’s a PublishIt Symbols and Slogans disk inside it. The disk read fine. I was able to catalog and import images to PublishIt 4.
October 20, 2016
You can compare to the previous post where I used the VGA video.
October 18, 2016
I was copying a number of print shop images from various SoftDisks to a single floppy. I was able to get 105 images on a single DOS 3.3 floppy. I then decided to test importing them to a PublishIt 4 document. Below are a couple pictures. The second picture is the print preview mode. This was running on my IIGS which has the VGA adapter from ManilaGear.com.
PublishIt 4 VGA adapter and Monitor
PublishIt4 Preview Mode
Packed with Print Shop Graphics